Alarm Lock DL1300 Manuel d'instructions

1 DL1300 Programming Instructions DL-WINDOWS PROGRAMMING SOFTWARE DL Trilogy Series Stand-Alone Access Control Systems OI311 7/06 345 Bayview Aven

10 NOTE: The AL-PCI cable is designed to be used on a 9 pin serial COM port. If your computer has a 25 pin COM port, a 25 pin to 9 pin adapter must

11 WIRING See the Installation Manual for more information. Batteries: Use only 3.0 volt Lithium Type 123 batteries (or equiva-lent). Two (2) batteri

12 Quick Start First Time Start Up 1. Unpack the lock. 2. With the batteries disconnected, hold down the ; key for 10 seconds and release. 3. Co

13 Quick Start (cont’d) Delete a User Code 1. Enter Program Mode (if not in already). 2. Press ; 2 ; [User Number] :. The lock will flash a

14 Function 1 Change Master Code See page 15 Function 2 Add/Delete/Change User Codes See page 15 Function 3 User Disable (By User Number) See page

15 1. New Master Code (User Number 1) 2. Add/Delete/Change User Codes 2-2000 ; 1 ; [ _ _ _ _ _ _ ] ; [ _ _ _ _ _ _ ] : (New Master

16 USERS (Continued) ; 6 : 6. Enable Total User Lockout Mode (This Function enabled through keypad only) 7. Disable Total User Lockout Mode (This Fun

17 ; 1 2 ; 0 0 0 : 12. Clear All Schedules and Timeout Functions Function 12 clears all programmed Schedules and all Timeout Functions. (To cle

18 GROUPS Group Enable/Disable with Timeout (Enter Timeout, XXX Hours) (Functions 25-34 are enabled through the keypad only) • Hours must be between 1

19 ; 3 8 ; [ _ _ _ _ _ _ ] : (Date) 38. Set Date • Use Month Day Year format - MMDDYY - Single digit months and days are entered with a preced

2 Table of Contents DL1300 Series Lock Features ...3 Supported Products ...

20 CLOCK ADJUST ; 4 3 ; [ _ _ ] : (seconds) 43. Speed Up Clock (This Function enabled through keypad only) ; 4 4 ; [ _ _ ] : (

21 49. Disable Permanent Passage Mode (This Function enabled through keypad only) 50. Return Lock to Normal Passage Mode Schedule (This Function enabl

22 ; 5 5 : ; 5 7 : 57. Print Clock Settings, Software Version and Door Number 55. Print Audit Trail ; 5 6 : 56. Print User Code List ; 5 8 : 58.

23 60. Number of Attempts Before Lockout 61. Set the Attempts Lockout Time • Number of attempts before lockout must be 1-9 attempts. • The number of

24 Scheduled Passage and Group Use the functions below to enable Passage Mode and enable/disable Groups at the time programmed. • For day enter: 1 for

25 QUICK SCHEDULES 84. Business Quick Schedule 7AM-5PM, Monday - Friday (This Function enabled through keypad only) ; 8 4 ; [ _ ] : (Group) ; 8

26 ; 9 9 ; 0 0 0 : 99. Clear All Lock Programming (This Function enabled through keypad only) Clears all programming, and returns lock to factor

27 Groups and Scheduled Group 1 Examples The following examples detail the more advanced features of the DL1300 series locks. Although all features

28 Groups and Scheduled Group 1 Examples (cont'd.) Functions 92/93: Use Function 92 and 93 (see page 26) to create a window of time where if any

29 Function Number(s) Function Name Programming 43/44 Clock Adjust 52/53/54 Pass Time (3 sec)  10 sec  15 sec  60 Set Loc

3 Audit Trail • 40,000 Event Capacity • Entries Logged with Time and Date • Critical Programming Events Logged • Printable using the AL-IR1 Hand-Held

30 User Number (1-2000) User Code (3-6 digits) User Name 1 2 3 4

31 User Number (1-2000) User Code (3-6 digits) User Name 1 2 3 4

32 User Number (1-2000) User Code (3-6 digits) User Name 1 2 3 4

33 Day(s) Function Number Up to 500 scheduled functions can be programmed. For Day Enter: 1 = Sunday, 2 = Monday, 3 = Tuesday, 4 = Wednes

34 Day(s) Function Number Up to 500 scheduled functions can be programmed. For Day Enter: 1 = Sunday, 2 = Monday, 3 = Tuesday, 4 = Wednes

35 ACCESS = Entry into a restricted area. AUDIT TRAIL = A date/time stamped log of previous lock events. CLOCK • REAL TIME CLOCK = An accurate built-

36 ALARM LOCK LIMITED WARRANTY ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing defects in materials and wor

4 Data Transfer Module (AL-DTM) An AL-DTM is used to transfer Lock Programs (and other data) between DL-Windows and locks. When computers cannot be

5 Lock Design Overview Why Use Software inside a Lock? With ordinary door locks, the need to make physical copies of metal keys and distributing them

6 Terminology Used in this Manual What is a Lock Program? A Lock Program contains the instructions that a lock uses to perform its various functions.

7 ory can be thought of as simply a numbered list from 1 through 2000. Each entry in the list is represented by a User Number. Therefore, where a Us

8 User 299 is a Non-Pass Code. This is the only code that will initiate data transfer with the AL-DTM. NOTES: The Programming Level defines the rang

9 ACTIVITY LED SOUNDER COMMENTS Keypress 1 RED Flash 1 Beep Normal Operation Access Granted 3 GREEN Flashes 3 Beeps Invalid Code 6 RED Fla