Alarm Lock DL5300 Manuel d'instructions

1 Trilogy Double-Sided DL5300 Programming Instructions Double-Sided DL Trilogy Series Stand-Alone Access Control Lock WI1672 1/08 345 Bayview Avenu

10 NOTE: The AL-PCI cable is designed to be used on a 9 pin serial COM port. If your computer has a 25 pin COM port, a 25 pin to 9 pin adapter must

11 WIRING See the Installation Manual for more information. POWER UP • When applying power to the lock for the f

12 Quick Start First Time Start Up 1. Unpack the lock. 2. With the batteries disconnected, hold down the ; key for 10 seconds and release. 3. Co

13 Quick Start (cont’d) Enter User Codes 1. Enter Program Mode (if not in already). 2. Press ; 2 ; [User Number] ; [new User Code] :. (For

14 Verifying Basic Keypad User Codes Test a valid User Code: • VALID CODE - The Green LED will flash momentarily and the sounder will beep a few tim

15 Function 1 Change Master Code See page 16 Function 2 Add/Delete/Change User Codes See page 16 Function 3 User Disable (By User Number) See page

16 1. New Master Code (User Number 1) 2. Add/Delete/Change User Codes 2-2000 (Access through either side) ; 1 ; [ _ _ _ _ _ _ ]

17 USERS (Continued) ; 6 : 6. Enable Total User Lockout Mode (This Function enabled through keypad only) 7. Disable Total User Lockout Mode (This Fun

18 ; 1 2 ; 0 0 0 : 12. Clear All Schedules and Timeout Functions Function 12 clears all programmed Schedules and all Timeout Functions. (To cle

19 GROUPS Group Enable/Disable with Timeout (Enter Timeout, XXX Hours) (Functions 25-34 are enabled through the keypad only) • Hours must be between 1

2 Table of Contents Lock Features ... 3 Supported Products ...

20 ; 3 8 ; [ _ _ _ _ _ _ ] : (Date) 38. Set Date • Use Month Day Year format - MMDDYY - Single digit months and days are entered with a preced

21 ; 4 5 : 45. Enable Passage Mode (This Function enabled through keypad only) ; 4 6 : 46. Disable Passage Mode (This Function enabled through keypad

22 49. Disable Permanent Passage Mode (This Function enabled through keypad only) 50. Return Lock to Normal Passage Mode Schedule (This Function enabl

23 ; 5 5 : ; 5 7 : 57. Print Clock Settings, Software Version and Door Number 55. Print Audit Trail ; 5 6 : 56. Print User Code List ; 5 8 : 58.

24 ;62 ; [ _ _ _ _ ] ; [ _ _ _ _ _ _ ] : (User Number) (User Code) 60. Number of Attempts Before Loc

25 ; 6 7 ; [ _ _ ] : (Event Number) 67. Add System Features SYSTEM FEATURES 68. Delete All Features added by Function 67. ; 6 8 ; 0 0 0

26 Scheduled Passage and Group Use the functions below to enable Passage Mode and enable/disable Groups at the time programmed. • For day enter: 1 for

27 QUICK SCHEDULES 84. Business Quick Schedule 7AM-5PM, Monday - Friday (This Function enabled through keypad only) ; 8 4 ; [ _ ] : (Group) ; 8

28 ; 9 9 ; 0 0 0 : 99. Clear All Lock Programming (This Function enabled through keypad only) Clears all programming, and returns lock to factor

29 Groups and Scheduled Group 1 Examples The following examples detail the more advanced features of the DL series locks. Although all features and

3 Audit Trail • 40,000 Event Capacity** • Entries Logged with Time and Date • Critical Programming Events Logged • Printable using the AL-IR1 Hand-Hel

30 Groups and Scheduled Group 1 Examples (cont'd.) Press ; 2 ; 4 ; 4 5 6 7 8 9 :. 3. Because User 4 does not have a default Group association,

31 Function Number(s) Function Name Programming 43/44 Clock Adjust 52/53/54 Pass Time (3 sec)  10 sec  15 sec  60 Set Locko

32 User Number (1-2000) User Code (3-6 digits) User Name 1 2 3 4

33 Day(s) Function Number Up to 500 scheduled functions can be programmed (Up to only 150 using AL-DTM). For Day Enter : 1 = Sunday, 2 = Mo

34 ACCESS = Entry into a restricted area. AUDIT TRAIL = A date/time stamped log of previous lock events. CLOCK • REAL TIME CLOCK = An accurate built-i

35 alarm panel during a predefined schedule. Should the Group 1 enter the lock outside of the scheduled time, the alarm will not disarm. The alarm pa

36 ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing defects in materials and workmanship for 24 months follow

4 Supported Products Data Transfer Module (AL-DTM) An AL-DTM can be used to transfer Lock Programs (and other data) between DL-Windows and locks. Wh

5 Lock Design Overview Why Use Software inside a Lock? With ordinary door locks, the need to make physical copies of metal keys and distributing them

6 Terminology Used in this Manual What is a Lock Program? A Lock Program contains the instructions that a lock uses to perform its various functions.

7 What is a User Number? User Numbers are used and are significant within each indi-vidual lock only. The User Number determines the Program-ming Le

8 USER TYPE USER NUMBER GROUP DEFAULT ASSOCIATION MINIMUM PROGRAM LEVEL (See page 6) Master Code 1 - M Installer Codes 2 & 3 none 4 Manager

9 ACTIVITY LED SOUNDER COMMENTS Keypress 1 RED Flash 1 Beep Normal Operation Access Granted or Remote Release 3 GREEN Flashes 3 Beeps Invali