Alarm Lock NETWORXPANEL Spécifications télécharger pdf (Page 4)

4 NX-592E NetworX Cellular Module Installation Sheet

installer code to check), you must change the wireless gateway

keypad address.

To change the gateway keypad address:

1. Press *, then 8.

2. Enter the “Go to program” code (the default code is 9, 7, 1,

3). If the code is valid the keypad display will prompt you

for a device address.

3. Enter the address of the NX-592E (7, 8) then press #. At

this point, the keypad display will prompt you for a

programming location to be entered.

4. Enter 0, followed by the # key. Location 0, which is the

LCD address will display. The default is 192. For a list of

address, see Table 3 below.

5. To change the LCD keypad address, enter the new

address, followed by the * key. The display will return to

the location prompt.

6. To exit this location without changing the data, press the #

key.

7. To review the data, repeat the above procedure, pressing

the * key without entering data first. If you attempt to

program an invalid entry for a particular segment, the

keypad sounder will emit a triple error beep and remain in

that segment waiting for a valid entry.

8. Press the Exit key to exit this programming level. Press

the Exit key again to exit Program Mode.

While in programming mode and not in a location, the number

in parentheses is the location you were previously changing.

For example, if the display reads “Enter location, then # (2)”, it

is reminding you that location 2 was the last location you

programmed.

Location 0: LCD keypad address

Certain commands in the module require it to know the location

of at least one LCD keypad (if one exists in the system). If

your system has an LCD keypad we recommend that you

place it in Partition 1 Keypad 1. This will allow Location 0

to be left at the factory default. If the LCD keypad is

selected as something other than Partition 1 Keypad 1,

program the appropriate address in Location 0.

Table 3: Addresses

Keypad

Partition

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

Cellular Status LEDs

The cellular radio status LEDs are five small LEDs located

near the bottom of the radio daughter board.

Figure 5: Cellular Status LEDs

Table 4: Cellular Status LED Functions

LED

Function

Error LED. Flashes 1 to 8 times in an 8-second interval to

indicate a specific error. See Table 6 for errors and

common fixes.

Panel Communication and Z-Wave status messages.

Flashes every time the module communicates with the

panel and flashes in patterns to indicate Z-Wave status.

Cellular Communication. Flashes every time the cellular

signal level is checked and when packets are exchanged

with Alarm.com.

Cellular Signal Level. Flashes 0 to 5 times to indicate signal

strength, or toggles on/off slowly when communicating with

Alarm.com servers.

Z-Wave Error LED. See Table 7 for error descriptions.

LED Details

LED L1 (red). L1 flashes when there is an error. The number

of flashes indicates the error number. If there are two or more

errors at the same time, the errors will flash one after the other.

The LED will stay off for at least four seconds between errors.

Table 5: LED L1 errors

Flashes

Error

Module cannot communicate with the panel. Perform a

power cycle on the panel. If the error persists lift the module

out of the gateway and re-insert it. If the error is still

observed try a different module. Finally, if that does not fix

the problem try a different panel.

The SIM card is missing. The SIM card holder can be found

on the module. Verify that the SIM card holder is closed

securely and that there is a SIM card in the holder.

2 then 4

The module provisioning process could not be completed.

2 then 5

The module provisioning process could not be completed

because the module is currently roaming on the carrier’s

network.

1 2 3 4 5 6 7 8 9 ... 12 13

Commentaires sur ces manuels

Pas de commentaire

Alarm Lock NETWORXPANEL Spécifications Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Alarm Lock NETWORXPANEL