Alarm Lock Trilogy DL4500 Manuel d'instructions

1 Trilogy DL4100 / DL4500 Series Programming Instructions WI1194B 12/04 © ALARM LOCK 2004 Alarm Lock Trilogy Series of Standalone Access Control Sys

10 NOTE: The AL-PCI cable is designed to be used on a 9 pin serial COM port. If your computer has a 25 pin COM port, a 25 pin to 9 pin adapter must

11 WIRING See the Installation Manual for more information. Batteries: Use only 1.5 volt Duracell Alkaline size-AA batteries. External Power: Red /

12 Quick Start First Time Start Up 1. Unpack the lock. 2. With the batteries disconnected, hold down the ; key for 10 seconds and release. 3. Co

13 Quick Start (cont’d) 2. Press ; 2 ; [User Number] :. The lock will flash a green LED and beep continuously for 6 seconds. When the red L

14 Function 1 Change Master Code See page 15 Function 2 Add/Delete/Change User Codes See page 15 Function 3 User Disable (By User Number) See page

15 1. New Master Code (User Number 1) 2. Add/Delete/Change User Codes 2-2000 ; 1 ; [ _ _ _ _ _ _ ] ; [ _ _ _ _ _ _ ] : (New Master

16 USERS (Continued) ; 6 : 6. Enable Total User Lockout Mode (This Function enabled through keypad only) Note: Do not use this function with Passage

17 ; 1 2 ; 0 0 0 : 12. Clear All Schedules and Timeout Functions Function 12 clears all programmed Schedules and all Timeout Functions. (To cle

18 GROUPS Group Enable/Disable with Timeout (Enter Timeout, XXX Hours) (Functions 25-34 are enabled through the keypad only) •Hours must be between 1-

19 ; 3 8 ; [ _ _ _ _ _ _ ] : (Date) 38. Set Date 42. Reserved •Use Month Day Year format - MMDDYY - Single digit months and days are entered

2 Table of Contents DL Series Lock Features ... 3 Supported Products ... 4

20 CLOCK ADJUST ; 4 3 ; [ _ _ ] : (seconds) 43. Speed Up Clock (This Function enabled through keypad only) ; 4 4 ; [ _ _ ] : (

21 49. Disable Permanent Passage Mode (This Function enabled through keypad only) 50. Return Lock to Normal Passage Mode Schedule (This Function enabl

22 ; 5 5 : ; 5 7 : 57. Print Clock Settings, Software Version and Door Number 55. Print Audit Trail ; 5 6 : 56. Print User Code List ; 5 8 : 58.

23 60. Number of Attempts Before Lockout 61. Set the Attempts Lockout Time Used with Function 61 •Number of attempts before lockout must be 1-9 attem

24 68. Delete All Relay Functions and System Options added by Function 67. Also Privacy Time-Out Duration. ; 6 8 ; [ _ _ _ ] :

25 Scheduled Passage and Group Use the functions below to enable Passage Mode and enable/disable Groups at the time programmed. •For day enter: 1 for

26 QUICK SCHEDULES 84. Business Quick Schedule 7AM-5PM, Monday - Friday (This Function enabled through keypad only) ; 8 4 ; [ _ ] : (Group) ; 8

27 To Disarm a Burglary Control Panel 90. Relay Activation (Open Time Window) ; 9 0 ; [ _ ] ; [ _ _ _ _ ] :

28 ; 9 9 ; 0 0 0 : 99. Clear All Lock Programming (This Function enabled through keypad only) Clears all programming, and returns lock to factor

29 Groups and Scheduled Group 1 Examples The following examples detail the more advanced features of the DL series locks. Although all features and

3 Audit Trail • 40,000 Event Capacity • Entries Logged with Time and Date •Critical Programming Events Logged • Printable using the AL-IR1 Hand-Held P

30 Groups and Scheduled Group 1 Examples (cont'd.) Functions 90/91: Use Function 90 and 91 (see page 27) to create a window of time where if an

31 DL4500 Residency and Privacy Features Residency Feature (Factory Default) The "Residency Feature" is provided to prevent a person from un

32 DL4100 Residency and Privacy Features Privacy Feature Mode 1: (Door Normally Locked--Factory Default) Programmable Through DL-Windows & Keypad

33 Function Number(s) Function Name Programming 41 Daylight Saving Time Code 43/44 Clock Adjust 52/53/54 Pass Time (3 sec) ! 1

34 User Number (1-2000) User Code (3-6 digits) User Name 1 2 3 4

35 Day(s) Function Number Up to 500 scheduled functions can be programmed (Up to only 150 using AL-DTM2). For Day Enter : 1 = Sunday, 2 = M

36 ACCESS = To allow Users to unlock the door temporarily to gain en-try. AMBUSH = A special Code entered at the keypad when the User is forced to un

37 • GROUP 1 ENABLES GROUP 4 USERS = A Group 1 USER CODE entry during a predefined schedule will allow access to Group 4 Users. • GROUP 1 PUTS UNIT I

38 NOTES

39 NOTES

4 Data Transfer Module (AL-DTM) An AL-DTM can be used to transfer Lock Programs (and other data) between DL-Windows and up to 48 locks. When computer

40 ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing defects in materials and workmanship for 24 months follo

5 Lock Design Overview Why Use Software inside a Lock? With ordinary door locks, the need to make physical copies of metal keys and distributing them

6 Terminology Used in this Manual What is a Lock Program? A Lock Program contains the instructions that a lock uses to per-form its various functions.

7 word "Slot" is also used. They all mean the same thing. Since User Numbers are fixed, knowing a User Number will spec-ify the associated

8 USER TYPE USER NUMBER GROUP DEFAULT ASSOCIATION MINIMUM PROGRAM LEVEL (See page 6) Master Code 1 - M (All Programming Abilities) Installer Codes

9 ACTIVITY LED SOUNDER COMMENTS Keypress 1 RED Flash 1 Beep Normal Operation Access Granted 3 GREEN Flashes 3 Beeps Invalid Code 6 RED Flas